This automated visual Fiber tensile screening system is designed for operator skill independent use within production and lab configurations. Two fundamental model configurations enable the user to select between a set up for regular linear Proof testing and with extra mandrels for rotary higher power testing.
The linear edition is made for production Proof screening with forces as much as 22 N. Motor-driven clamps with carefully designed rubber inserts ensure that the Sheathing Line is not damaged in the testing procedure whilst at the same time getting rid of the need for another air provide. Degrees of tugging force, pulling velocity and hold time are programmable and conveniently accessible to the owner with the built-in LCD touch-screen manage. Information from tests can be stored and reached through the USB port or Ethernet user interface.
Mandrels of the identical design like NYFORS’ optical Fiber recoaters can be mounted on the Proof tester inside the rotary higher power settings. The Fiber is covered round the two mandrels which assistance it with a unique clamping mechanism. By doing this higher lots can be used to the Fiber, enabling breaking strength assessments under controlled circumstances.
Adjustable clamp positioning facilitates screening with all the highest force amounts as well as testing of short Fiber measures. The compact and light weight design definitely makes the tool simple to maneuver in a lab environment as well as integrate in a creation work table in which space is at reduced. The machine is really a compact and lightweight tool perfect for screening the potency of optical fibers up to 30 N. The equipment is created to meet all kinds of programs in which a power test has to be performed.
The machine is made using the user in mind. The Optical Fiber Proof-Testing Machine is readily placed in the carefully guided linear clamps, as well as the screening begins instantly with a “One Touch” go switch. The built-in microprocessor regulates all the essential parameters such as pulling force, tugging speed and hold time. This enables for a totally controlled check each time.
The device can be attached to an outside Computer, which allows use of all programmable parameters and configurations. The equipment is adapted to stand-alone use or the integration into different subsystems. The equipment posseses an extensive capacity for logging and conserving details such as tugging force, pulling speed and Fiber size and other guidelines.
Two recoat injector configurations can be purchased. The PTR307 uses a computerized water pump to inject the recoat materials. The quantity of materials dispensed from the automatic injector is managed by hand through the top-mounted “Inject” button or programmed into the machine utilizing the tablet controller. The PTR307B comes with a handbook recoat shot program that requires the consumer to manually dispense the recoat material to the mold cavity; a substitute injector for that PTR307B recoater is available below. Please note that this automated injector is only compatible with higher-index recoat material, as the handbook injector is compatible with each low- and- index recoat material; both of them are sold separately below. Make sure you contact Tech Support to learn more.
he manual injector can be mounted to suitable Fiber recoaters via the 4-40 screws on the recoater housing (see photo to the right). Utilize a 3/32″ hex key to secure the injector prior to use. To get in touch the PTRRRM for the recoater mold, tighten up the connector at the conclusion of the eco-friendly plastic tubing, then loosen by a 1/4 consider enable rotation.
The injector is equipped with a syndication device and 2-position selection handle for directing the stream of recoat materials. A knurled dispensing attach with the inner plunger acts as a syringe for the recoat materials. To fill the syringe, point the lever downwards (i.e., towards the recoat bottle), then rotate the knurled dispensing attach counterclockwise until it rotates easily to fill the syringe (demonstrated inside the photo towards the right). Then, to inject the recoat materials in to the mold, point the lever horizontally (i.e., facing qyjflh knurled screw) and spin the screw clockwise till near the finish in the travel range is reached. Steer clear of bottoming out the dispenser as this may damage the internal plunger; also be careful when re-engaging the threads to prevent go across threading the dispensing screw. A number of fill up/inject actions may be required till air is displaced in the program. Use lens tissue as well as an acetone or alcohol cleansing solution to gather FTTH Cable Production Line materials that runs from your mold.